Organize Your Hardware! In the Wall Hardware Storage

Articles, Blog

Organize Your Hardware! In the Wall Hardware Storage

Organize Your Hardware! In the Wall Hardware Storage


in this video Im going to be tackling a
project I have personally been wanting to do since building this shop in the
wall of hardware storage now before you go freaking out on me in the comments
it’s important to note that this is an interior wall they hold 157 containers
total and it was very simple to do so let’s get into it this is the dividing
wall between my metal shop and my woodworking shop I started by unscrewing
two panels on the far right of it and moving the sheets out of the way my
original plan was to rip both or by 8 sheets down the center place the top
half of the top sheet and then lower half of the bottom sheet back into place
and then have the containers in between this would allow all containers to be
within my reach when standing flat-footed on the ground with that I
used my track saw and rip down the boards in the middle then I went back to
my wall and started clearing out the spray foam insulation as I said in the
intro this is an interior wall so I don’t mind giving up the insulation here
my intent was to build a shelving system made from datas essentially that would
accept a plastic storage container I found that fit perfectly inside my wall
okay let’s build some dado shells NATO shelves yeah I think that’s a
fitting name to make these I started by grabbing my dado stack and placing half
an inch and my table saw I’ll be using a half lap jig made by rockler to make
sure I can get these repeatable cuts accurate and both spacing and size the
jig is intended to be used for single pass operations but since dado stacks
don’t go up to one inch which is what I need to cut to be at I did a test piece
to figure out how to make it work for a two pass operation I started by cutting
in a rabbet on the end then measuring over the distance I wanted between my
containers and making a mark I butted the edge of my rabbit up against the
metal key then adjusted the fence over so that my mark was in line with the
blade I pushed it through to make the cut then move the board over so that the
fresh bado was now setting up against the middle
and then I continued the process to make the second pass to enlarge the dado I
repeated the same process I started with my rabbit lining up the stack so that it
was just outside of the first pass once it was cut in I pushed the inside edge
up against the metal key then adjusted the fence on the jig so that the stack
lined up perfectly for my next cut this locks in the spacing so now I could make
the cut then as long as I place the inside edge
up against that key it would hit where I needed it to and enlarge the data to one
inch since I plan to do plenty more of these boards I made two pencil marks on
the top of my fence to mark each location also I do have a free diagram
for these on my website if you’re interested when making the dados I left
my boards wide enough to create matching pairs of shells to get individual
shelves that use my truck salty split it right down the middle doing it this way
ensures that they in fact match and the slots will line up perfectly with one
another I repeated the process because the studs being 16 on center is just
wide enough for two rows of container in fact it’s actually just a tad bit too
wide I did a mock up on my workbench before putting things together and I was
short by exactly half an inch that’s an easy fix though I cut a piece of
half-inch plywood down to the same size and I stuck it in between the two inside
shelves and there that is a perfect fit the outside shelves are simple enough to
attach as they go directly on the inside face of the studs however I did stick a
countersink bed in my drill and pre-drilled the placement holes this way
I can move my mobile workbench into place then easily attach the unit won’t
holding it in position you’ll see that I started off quite small and that’s
because I wanted to test that this would actually work before diving in but so
far so good I would say moving on to attaching the center
section for this part I started off using pocket holes I pulled out my
armored coal jig and drilled in know about four holes along this length
remember that armor made the height of the jig the same as
two by four so that you can easily play supports under longer work pieces once
it drilled in the pocket holes I did a few more countersink holes then attached
the dado shells to the center filler piece of ply I once again prepped by
placing screws in the pockets before setting it in place then adjusted the
left and right position so that the gap was equal on both containers it is
working already theory is proven I felt like I had a
working system so I continued on this time I cut dedos and larger sheets that
would fill up the entire length of the Bay in fact I used the hot sheet I
wouldn’t be placing back on the wall to make up all of my shelves which meant
that I didn’t have to buy any material for this project while I’m working on
that I want to thank this video sponsor which is Skillshare you’re not already
familiar Skillshare is an online learning community with over 28,000
classes in many different categories there are so many different courses from
starting an online business to online marketing to more creative ones such as
learning to paint or leather working while exploring all that skill share has
to offer I stumbled across as interesting circular logo design course
from Aran droplet before I knew it I learned lots of tips and tricks to
create circular logo designs which is super helpful in my business when
creating things like a logo for Instagram or creating new stickers to
share so if you’ve been wanting to learn more in business or to explore more on
the creative side I’m sure there is a Skillshare course to help you well for
less than $10 a month you can get a premium subscription to Skillshare and
get unlimited access to their entire library of courses and even better
Skillshare is giving the first 200 people two months for free so click the
link down in the description and use my code at checkout to get two months of
Skillshare for free a big THANK YOU to Skillshare for supporting my channel and
what I do I repeated the process to hang things but this time after the first
shell went up I used a level and a scrap piece of wood to make sure that they
were truly in line with one another oh boy my mom’s gonna kill me when she sees
I use my teeth it turns out you’re never too old to get chastised by your mama
you can see I just spanned a the distance with the wood and place a
level on top I did the same thing when it came time to install the center
section but instead of using a piece of wood I inserted two containers with the
front lip poking out and placed my level across their front on this one my stud
Bay was just slightly off 16 Center and I didn’t need the half-inch space there
between my Center shelves just noting to be sure to measure each stud Bay before
making your components so that you know how much to compensate if at all so it
was when I was attaching the second long Center that I started rethinking my
design I was worried that a few pocket holes wasn’t going to be enough support
once I had all of these containers filled I ended up taking it down and
making a flange for it instead and this is just a piece of ply that I made a few
inches wider than the shelves and attached it directly to the baptists
screws to make this easier I made a quick spacer I not only use a spacer to
align the shelves perfectly Center along the length of the flange but also as a
guide on where to drill my holes so that I could hit wood and not a dado I also
use the countersink here to make sure the screws wouldn’t be proud in the back
surface this is important because next I place the center section back into place
and use the plans to attach it to that back wall the next Bay was exactly the
same except on this one I had a wire running down one of the studs to
compensate for this I built some small standoffs on the back of one of the
shelves and this allowed me to straddle that wire so it wasn’t crushed or in the
way but I could still attach it to the inside face next I did the center
support and then just repeated the process on the last Bay now something I
wish I would have done more of adding in small containers these look small but
are actually a very useful size and the box comes with a ready-made shelf I
didn’t see the sense on making something new when it came with something
perfectly fitting so I just took the container to my bandsaw and chopped it
up then I made some shelves for them to
rest on see the rows were about one container too short to fit nicely
between the studs so after cutting up the rows I also cut up one single row
into individual cubbies so that I can add one cubby to each row if that makes
sense the visual will make sense after
attaching the wooden shelves I use some quick setting and multi-surface glue
from tight bond called thick and quick I placed them on the bottom of the rows
then clamped it in place for a short time to attach them it’s always
surprising to me just how often these small Bessie C clamps come to the rescue
alright while this we’re setting up I cut and attach some flat shows to the
other stud base as I said in the start I plan to use half and half of each
section but I diverted off of that plan when I opened up the wall and saw all of
my wiring that’s why I went taller than I originally expected already and the
last finishing touch was reattaching all of the sheathing I took down and the
start to cover back up the insulation parts then I was just a matter of
filling it up total this holds 142 of the larger containers and 15 of the
smaller ones although I might come back and add in more of these smaller ones oh
and for a labeling system I kept it very easy and adjustable instead of a label
on the outside when I emptied a hardware box inside of a container I simply cut
out what it was stuck it inside the container and faced it outwards now I’ll
be able to easily see what it is I need pull out an entire container and take it
to wherever I’m working now I imagine that people are gonna say that this is a
lot but remember whenever you’re building storage solutions that if you
build it to your current inventory it’s already too small you’re gonna go
through the effort of a project go ahead and build in some extra room for growth
then you’ve enjoyed this project more than
that it’s a party to get out into your own shop and organize a section of it
when your comments on what you think down below and that will see you on
whatever building next

100 thoughts on Organize Your Hardware! In the Wall Hardware Storage

  1. April, wonderful! I've been describing this idea for the wall in our entry area for decor purposes. The dead corner space in the kitchen, shares the entry stair wall. You've demonstrated what I want for a space that has no room for an entry table! Thank you!!!

  2. Hello
    I am very appreciative to see everything you can do for a woman.
    it's great, go go women.

    excuse me for my English.

    steph from Belgium

  3. First I practice my English. Second I enjoy a beautiful lady. Then I enjoy a very useful and practical project. I think that it was 3-in-1. Perfect. Thanks a lot.

  4. 1:12 where did you buy these from? what size or upc or product code / model number Sterlite ??? PLEASE and Thank You…..Like your vids too! ;-D

  5. Hey nice job April.Do you think you could do a detailed video on making plywood cabinets.not slot on the subject on youtube.

  6. Love your channel😀 great projects 👍 would like to see you build a freestanding pantry cabinet. Thank you for sharing your talents. Always fun and educational 😉

  7. Great Job April!!!
    I have done something similar; at most lumber companies or big box stores they have a product for wire hanging displays and come in 4X8 sheets. Grooves are already in place and the grooves are 1/2" wide and deep. Perfect for plastic totes. Just a thought for those who are without dado heads or routers. Nice video!

  8. It is interesting to see the creativity in the field of carpentry despite different cultures please … I hope to benefit more science .. Thanks to the knowledge

  9. another bad thing is putting your hands behind, or neer the tip of a staple gun, you could penetrate your hand with the nails!!

  10. Yet another brilliant project but looking at the height of the storage against you April a rolling folding step ladder might be good project

  11. I think this is a very efficient use of space – like a storage niche – but in all caps so it's represents how many containers you have – storage NICHE!. As long as you don't put something in front of those units you should be fine. You might need a small step stool to get to the very top rows.

  12. Really awesome organizer. I would love to do this or to organize my shop but I am in the bottom of a pa bank barn with field stone walls. I would rather not cover them for aesthetic reasons. Any thoughts?

  13. Just be sure to buy some extra containers to replace the ones that break or wear in the future. Always seems like I build something using a product as a base part and the company stops making that item 6 months later…

  14. April I know you used a level and all but from our point of view the 3rd and 4rth column seem to be tipping into each other especially near the bottom am I wrong

  15. Richard Longoria
    April love the storage but where did you buy the plastic containers and what size are they?
    Any help will be greatly appreciated.
    Richard in Texas

  16. i watched a vid where the guy made his own boxes and put a french cleat on the front as a pull handle then he could hang them on cleats around his shop near his projects

  17. I like the simple labelling system. When you need more of the same hardware simply take the label with you to ensure you buy the correct product.

  18. IDK, April. You have a huge (envious) shop. I think surface mounting your stuff on the wall would have been just fine, and more adaptable for future growth and changes. Other than that, I love your website. And I also admire how your skill set has grown over the years!

  19. Love the mountain/sun artwork in the background. Gives me an idea for my camper with round windows – replace the sun with the window. Great videos!

  20. Great setup! I can't build inside my wall. I like this idea though. I'm going to try something similar, but movable wheel base. Maybe even 2 sided.

  21. Awesome video. Thanks for sharing. I plan on using this storage solution for my MakerSpace. I also plan on showing this video to my Maker class. It will be great for inspiring the kids to think through, plan and adjust what ever project they might attempt. I love the fact that you take us step by step through your plans and show us your adjustments to the plan as issues arise during assembly. It's also refreshing to see a lady doing what she loves to do. You are a great role model (for both girls and boys). And it doesn't hurt being from Ohio either!
    Thanks again. Looking forward to seeing what yo do next.

  22. OMG. I'm in love. That's the best storage idea ever.. I've watched your channel here and there. But now I'm hooked. So thanks for the awesome sauce, video!

  23. I agree Alan S many of the boxes are not level and I agree with kettle vale cut short pieces and pin and glue rather than the dados the whole thing is overkill and the average person would not need anything like as many boxes

  24. I am absolutely worry to see you to touch the saw blade with your fingers even though the blade is not really moving. Be safe! Thank you for precious info./ Indonesia.

  25. Rebate in the UK, Rabbit has a fluffy tail and is useless in carpentry. Not picking on you, it hurts my OCD when watching american channels, Love this design and a good use of space.

  26. hahahahah i just got through listening to yalls old pod cast with nick ferry and jay. and all i could think of while watching this was…. 'If Nick could see her now." love it chica!!! very creative and resourceful. just like you've always been. keep up the good work!!!

  27. I'm wondering what store she was at where these boxes were $1.00 at (seen at 1:10 in the video)… anyone know? Buying several dozen at that price could saves some bucks.

  28. creo que hubiese sido mas practico haberlo hecho antes de poner el muro de tabla, es decir armarlo abajo y no al aire.. yo lo armaria primero todo y despues lo colgaria a la pared.¡

  29. Thanks again… another project i need.. I was going to go to harbor freight and get their small storage system. ( i still might do that) but this makes a lot of sense. Thanks!

  30. Hi April, I wish I could have all your tools and equipment! I like watching your channel soooo much even I haven’t built anything! Lol.

  31. Why did your inside walls have insulation to begin with? Was it soundproofing, no additional costs, a requirement for building codes?

  32. Всегда с удовольствием смотрю Ваш канал. Хорошая идея для мастерской. Спасибо.
    I’m always happy to watch your channel. Good idea for a workshop. Thank.

  33. pretty awesome there girlie. keep it up. I've been a carpenter for a lot of years whom never watches this stuff online. You've had my undivided attention for 2 hrs at least. Great Work, and I really like your style and taste!

  34. Just could have used small planks with a distant holder between every plank for spacing room, would be less stressfull for the saw blades!
    Other than that a really great job thnx for sharing.
    Greetings.

  35. Love the idea . However, for every day garages this is a no go for fire safety. Plans for a cabinet with the same features would be great for those of us who are shop challenged. Definitely bring it down to reachable level safer as you grow older!

  36. Buona giornata bellissima dalla maualita stupenta complimenti x il tuo laboratorio e la sistemazione degli attrezzi 👏

  37. As an oil painter, this would work fantastic for my oil paint tubes and even the jars of thinner, and the jars of medium….I might have to adapt it a little but this is great!

  38. The dados seem so deep versus the sheet material thickness: rather weak. So I'd have considered offsetting each alternating column with half a container's height — then each thin piece is backed with a thick one. Of course the stud wall every two columns already helps you here, but if anyone makes this more freestanding that would help.

  39. I'm just confused on how this is not the same level of work as just cutting plywood as small square as use them purely as the bracers, and then jut glue them up with a spacer and a nail gun.. Or just pop a couple of screws in each one cause what if you run out of the containers, due to breakage etc.. you can then just remove a section of the plywood with a couple of screws, make new bracers to fit the new replacement containers… In that section… Cheers to each their own if you enjoy this way of doing it.. One also a way you could just cut larger slots, "oblong hole" and then use a bolt with washers that you would sink, that could actually raise and lower the wood bracers thus solve having to alter this for new a new container later on over the years.

  40. I use computer paper boxes labeled double stacked on movable shelves.. top box use a lot bottom less.. lids on them plus they actually fit a lot of stuff.. by use…electric etc..auto stuff… nothing fits those containers.. it must be adaptable to different items…. me a pro handy person… moved way too many times…it must be portable and flexible..

  41. nice idea but you could have gone a bit lower and not so high… ewww cleaning out spray foam.. terrible job to have to do! you screwed your center holders to the plywood behind it? Ah! better way! Not bad.. But I would still have not made it so tall.. Just for ease of use.. But then I am old and the knees just do not like ladders!

Leave a Reply

Your email address will not be published. Required fields are marked *